Ghost Controls Access Control Installation Nationwide

Ghost Controls Access Control Installation: The Long Beach Owner’s Guide

If your Ghost Controls keypad, receiver, or access control board has quit or is working intermittently, we can usually get it matched and replaced the same week, often the same day we diagnose it. Installed price for Ghost Controls access control replacement in Long Beach typically runs $240 to $480 for keypads and receivers, or $320 to $650 when the main control board needs replacing, which includes the part, labor, and programming. Most owners call us after the keypad lights up but won’t release the gate, the remote works but the keypad won’t, or the whole system stops responding after a power surge. That’s a Ghost Controls access control failure, and it’s fixable without replacing the whole gate motor.

Call (562) 512-6788

Which Ghost Controls Models This Applies To

We work on all Ghost Controls gate opener series, including the TSS1, TDS2, TSS1XP, and TDS2XP models, plus the older Ghost Controls kits sold through big-box stores in the 2010s. The access control side includes the AXS-1 keypad, the AXS-2 push button, and the receiver board inside the main control box. Ghost Controls uses a proprietary radio protocol, so a LiftMaster or Mighty Mule receiver will not talk to a Ghost Controls keypad, and we run into owners who’ve bought a universal receiver online and can’t figure out why it won’t pair.

When you call, we’ll ask for the model number on the side of the control box and the part number on the old keypad if you can read it. Ghost Controls changed connector types between older and newer control boards, so a keypad that worked on a 2015 kit may not plug into a 2024 board without an adapter harness. Cole Rafferty has swapped enough of these to know which combinations work without guesswork. We always check the board revision before we order anything.

Signs Your Ghost Controls Access Control Installation Is Failing

• Keypad lights up but the gate won’t move. The keypad itself is sending the signal, but the receiver board inside the control box isn’t decoding it. We see this most often after Long Beach’s damp, salty morning air gets into the control box seal over time.
• The gate opens for the remote but not the keypad. That usually means the keypad battery is dead or the keypad lost its programming, not a board failure. We can re-pair it in about 10 minutes, and if it won’t hold programming, we replace it.
• The gate only opens when you’re close enough to touch it. This means the receiver antenna or receiver module is weak. Ghost Controls receivers degrade gradually in coastal air, and you’ll notice the range shrinking months before it quits entirely.
• Multiple accessories stopped working at once. Keypad, push button, and remote all dead usually points to the access control board itself, not a single accessory. That’s a board-level part, not a keypad swap.
• You hear a click but nothing moves. The access control is doing its job; the problem is downstream in the motor or the capacitor. We test the board output with a meter before we replace anything so you don’t pay for a board you don’t need.

Replacement Cost & What’s Included

For a Ghost Controls access control installation in Long Beach, you’re looking at $240 to $480 for a keypad or receiver replacement, and $320 to $650 for the main control board, installed. The spread is driven by which part is actually bad, how old the unit is, and whether we need to run new low-voltage wire from the keypad to the control box. Long Beach yards with mature landscaping tend to chew up buried wire, and we’ve pulled more damaged low-voltage wire out of flower beds near Bixby Knolls than anywhere else we work.

Every Ghost Controls access control installation we do includes the part, the labor to remove and mount, programming the new part to the existing opener, and testing the full cycle, open and close, at least five times. You get a written price before we touch anything, so if the bill ends up $480, you knew $480 was the number going in. No surprise line items at the end.

DIY or Call Us?

Ghost Controls access control parts are low-voltage, so you won’t get hurt replacing a keypad or receiver. The honest truth is most owners can swap a keypad themselves in about 20 minutes with a screwdriver and the instruction sheet. Where DIY goes sideways is when you can’t tell the difference between a bad keypad, a bad board, and bad wire, and you start throwing parts at it. We’ve had owners buy three different parts online before calling us, and the bill would’ve been half if we’d come first.

If you enjoy the project, we’ll sell you just the part and tell you how to program it over the phone. If you’d rather have it done right the first time, call (562) 512-6788 and we’ll schedule a diagnosis. The diagnosis is free, the quote is written, and you don’t pay anything until you approve the work.

FAQs

Call Warden Gate Repair Long Beach for Ghost Controls Access Control Installation

If your Ghost Controls keypad, receiver, or board is failing, call (562) 512-6788. We’ll send a technician whose name and photo you get before arrival, with a written price before any work starts. Every Ghost Controls access control installation we do in Long Beach is backed by the 365-Day Done Right Promise, which means if it’s not right, the return visit is free. We service Ghost Controls alongside LiftMaster, Mighty Mule, DoorKing, and the rest of the major gate brands, and we stock parts on the truck so we’re not making you wait on shipping.

Written by Cole Rafferty, Owner & Lead Technician, Warden Gate Repair Long Beach, serving Long Beach and nearby areas.